How to inspect termite infestation free

Tips for Termite inspection

How to inspect termite infestation free

OVERVIEW: inspect your house at least once every year for termites.

You have to inspect your house at least once every year against termite infestations. How do you inspect a house for termites?
Doing termite infestation checks yourself can be difficult, however the underlisted steps will aid you do comprehensive termite inspections in your home.

Though this guide will give ideas on how to inspect termite infestation free, We highly recommend getting a pest control professional to do this inspection for you, especially if you have a house with woods trusted to the earth or if your house has combination of areas that may be difficult for you to fully check.

Tools you will need to inspect termite infestation

Bright touch light
hand-held knife or flat-head screwdriver
Coveralls

What are the signs of termites in your home?

There are so many signs of termites in your home
Step 1: Signs to Look For when carrying out termite inspection
Termite inpection is actually a dirty job. That is why we recommend a coverall and a pair of hand gloves. For the dark areas in your house, you will need a bright touchlight. The knife or the flathead screw driver will help you pears into wood to acertain areas of weekness which may indicate termite infestation

We earlier discussed the signs to look out for when carrying out termite infestation checks… However we still ahd to cover this sub-topic below to further explain more:

1. Demaged or spoilt wood: Termite infestation on a wood may make the wood look crushed especially at structural joints. If you hit wood infested by termite, you will hear a dunging sound, indicating some vacumm within the wood. You can also lightly scrape wood surface to expose termite tunnels.

2. Hips of fallen wings.: Before termite swarmers move to their next develpment level, they shred off their wings, there by living the place with piles of wings

3. Mud Tubes. Some kind of termites do make their home under the ground and thereafter build tunnels called mud tubes. This mud tube can be vertically or horizontally built to connect the termite nest to a wood food source. Mud tubes are sure signs of the presence of termite around your home

Potential areas to look out for termites infestation

The following areas are places you ned to watch out for during termite inspection excercise. You should also note that termite are found close to the ground level
1. Cracks on the wall, expansion gap where termite can possibly gain access
2. piles of wood and wood debris near home
3. Slaps, steps, porches and other specific areas were wood meets concretes
4. wooden frames, window sills, sub floor, wooden porches or desk
5. Wooden components of construction in basements

Termite treatment process

If you locate an active subterranean termite infestation around your home, you are advise to carry out a 2 steps termite elimination process. if it is possible you may have to treat directly the active infested area found. you will also need to do a soil treatment to totaly eliminated the termite from the location and the colony if found.

Although you can safe some money, carying out the treatment of termite yourself, it can be time consuming and difficult. If after going through this step by step guide on termite treatment, you don’t feel OK carrying out the termite treatment process by yourself, I encourage you to hire the services of a professional termite control company or pest control company to do the termite elimination process for you.

STEP ONE: Directly treat the termite nest

I recommend a direct treatment of the termite nest directly, that is if you are able to find out the indoor nesting place. There are many termite elimination product in the market and we advise you to use the non-repellant or non-detectable products as the affected termite will pick it up and transfer it to others within the colony. Non-repellant product is of 3 types: The concentrated liquid, ready to use foams, aerosol sprays. The type of termite treatment formular you chose is decided by the area affeted and also on personal grounds.

Opening holes in woods or walls

This is done to gain access to suspected area to apply the termite treatment formular, you may aslo need to drill holes into walls around the affected areas. Apply the termiticide into the affected areas.

READ ALSO:   5 Best Termite Inspection and Control Companies in San Francisco, CA

STEP TWO: Termite trenching

We suggest managing the outside wall in the region where the infestation was discovered with a non-repellent concentrated termiticide such as Taurus SC.Treating the surface of your property near the location of the infestation is necessary for two reasons.

It’ll insure that the sub colony that was gathering food in the framework will soon be eliminated while they exit the home (this is especially important if you’re incapable of directly address the nest.
It’ll end new colony members from stepping into the home.
The treatment outlined under is standard and is detailing a subterranean termite treatment on a home or design that has been developed on a monolithic slab. When you yourself have a question in what that’s, or when you have a property on a get place, an empty stop base, a framework on piers or perhaps a structure on a floating slab, we suggest you give us a phone at 866-581-7378. We will walk you through the treatment process for your unique situation. Please recall to see the whole item label for total instructions.

Resources Required:

Trench shovel or choose axe
5 gallon ocean
Hand pump sprayer
Instruments needed if you have concrete interrupting areas that need to be trenched:

Claw drill (can be rented at home development stores)
1/2″ x 18″ or 1/2″ x 24″ cement exercise bit

Dig trench:

Utilising the select guitar or trenching shovel, you need to dig a 6″ wide by 6″ deep trench directly against the foundation of the exterior wall where in fact the termites were found. The building blocks of your dwelling will make up one area of the trench. The trench should be at the very least 10 linear legs long or expand down the whole external wall that was infested.

Mix termiticide solution:

After the trench is finished you can mix the termiticide solution. We suggest utilising the 5 quart bucket for this step. Fill the ocean with 4 gallons of water. Include the proposed quantity of concentrated termiticide as per the item label. Stir the answer completely with a paint stirrer and other tool before targeted liquid is equally distributed in the water.

Use solution to the trench:

You will need to serve 4 gallons of completed finished solution in every 10 feet of the trench. Make sure you serve slowly to make sure the solution is equally distributed.

Address the soil that has been removed from the trench:

While moving the soil you removed from the trench back into the trench you require to be sure it can also be handled with termite solution. Utilising the hand push sprayer laden with one gallon of finished termiticide solution, apply down the soil while changing it back in the trench. Apply the earth only until moist.

Positioning through cement:

If cement like a carport piece or pavement is against the building blocks in the area wherever you’ll need to deal with, you will be necessary to punch through the concrete to use the termiticide solution to the soil. Utilising the claw exercise with a 1/2″ x 18″ cement punch bit, turn out 2-3 inches from the building blocks and exercise holes every 12″ in to the cement along the inspiration wall.

You’re not merely drilling through just the concrete here, but in addition as serious as you can to the dirt. The deeper the better. After the openings are drilled, you fill at exactly the same rate you did the trench, 4 gallons per 10 feet. In the event that you drilled the openings 12 inches apart, then you definitely would have 10 openings over 10 feet that you are trying to fill with 4 gallons. This works out to be a small significantly less than half of a quart per hole. To load these I’d recommend utilizing the one gallon sprayer on a “pin supply” setting in order to power the fluid down the opening and perhaps not dash it everywhere. You may also use a channel and fill the termiticide down the holes. It’s hard to obtain 4 gallons per 10 feet in the openings, therefore it is essential that you use a extended punch touch, at the very least 18″ extended so you can bore out enough soil to carry the termiticide. Occasionally the ground is gradual to soak up the termiticide you invest the holes. You might need to load the holes, then move work with something different for an hour or so, return and load them again, move work on something else… 3 to 4 occasions to get the appropriate volume down the holes. After the holes are filled all that’s necessary to accomplish is area them with a cement repair product you can buy at a home improvement or electronics keep or you should use our Trebor plugs that may close the gap with no concrete mess.

These is how to inspect termite infestation free. Thanks for readi

ALSO READ: Termite Control – How to Get Rid of Termites

About umoh

The CEO and founder of Business Ideas Incubation Services.Our services includes: Professional business plan writing for venture capital, market research and analysis, Feasibility studies and startup business consulting.+2348140970926

....Comment below

%d bloggers like this: